高隔間的安裝方法是怎樣的呢？下面就來看看相關的內容吧。

　　What is the installation method of high compartment? Here's a look at the relevant content.

　　根據施工圖示結合實地的測量，從地龍骨內天龍骨下邊線尺寸，減15毫米20毫米為豎龍骨實際切割尺寸。把豎龍骨兩端插入直角連接件，放入地龍骨槽內，搭接天龍骨，把天、地龍骨與連接件用頂絲固定，豎龍骨與天龍骨縫隙不大于5毫米，與門框相連接的兩側豎龍骨是落地安裝。

　　According to the construction diagram combined with the field measurement, the actual cutting size of the vertical keel is 15 mm to 20 mm from the inside of the ground keel to the lower edge of the sky keel. Insert both ends of the vertical keel into the right Angle connector, into the keel slot, lap to the day keel, the day, the ground keel and the connector fixed with the top wire, the gap between the vertical keel and the day keel is not greater than 5 mm, and the door frame is connected on both sides of the vertical keel is ground installation.

　　根據圖紙和實地放線位置，把門和轉角的位置預留，地龍骨用脹栓固定于地坪上以螺絲固定地龍骨固定點間隔約一千毫米，需先在兩端約一百毫米位置固定。用墨斗線或水準儀在豎龍骨上確定橫龍骨安裝位置。把橫龍骨兩端插入直角連接件，放入左右豎龍骨之間調整所需上下間隔尺寸。

　　According to the drawings and the location of the field line, the location of the door and corner is reserved, and the keel is fixed on the floor with φ6 expansion bolt to fix the keel with screws at an interval of about one thousand millimeters, which needs to be fixed at both ends at about one hundred millimeters. Use ink line or level to determine the installation position of the horizontal keel on the vertical keel. Insert both ends of the horizontal keel into the right Angle connector, put it between the left and right vertical keel to adjust the required upper and lower spacing size.

　　安裝天龍骨扣條，把扣條扣在天龍骨兩面，用橡皮錘敲擊扣條，使扣條扣入天龍骨槽內。接縫處要緊密，注意扣條拼接處位置要合理、協調。然后，安裝豎龍骨扣條。測量地龍骨上邊線天龍骨扣條下邊線尺寸，要求切割尺寸，采用凸起帶槽扣條或凸起平板扣條。把扣條扣在豎龍骨兩面，用橡皮錘敲擊扣條，使扣條扣入豎龍骨槽內，拼縫處縫隙不得大于0.3毫米。帶槽扣條可根據需要中間插裝裝飾條。

　　Install the keel buckle, buckle the buckle on both sides of the keel, hit the buckle with a rubber hammer, make the buckle buckle into the keel slot. Joints should be close, pay attention to buckle splicing position should be reasonable and coordinated. Then, install the vertical keel buckle. Measure the size from the upper edge of the keel to the lower edge of the keel buckle. Cut the size according to the requirements. Use raised buckle with groove or raised flat buckle. Buckle the buckles on both sides of the vertical keel, and hit the buckles with a rubber hammer to make the buckles fit into the vertical keel slot. The gap between the seams should not be greater than 0.3mm. Slotted buckle can be inserted in the middle of the trim as required.

　　濟南高隔間系統安裝程序：安裝一側面板→配合交叉作業→放置巖棉→安裝另一側面板實體面板安裝(飾面石膏板、裝飾布和三聚氰胺飾面板)裝飾布飾面需用紙面石膏板板(8毫米9毫米厚)，采用膠把布平整粘貼后熱壓處理，用鋼制訂書釘把裝飾布邊在面板背面固定。木質板材用電切割鋸裁切好。

　　Ji 'nan high compartment system installation procedures: Install the side panel - work between cross - put the rock wool - another side panel entities panel installation (veneer gypsum board, decorating and melamine veneer) decorative veneer need gypsum board plate (8 mm to 9 mm thick), using environmental protection rubber cloth paste level off after extrusion processing, steel making staple the vestee edge fixed on the back panel. Wood plate cut with electric cutting saw.

　　高隔間的安裝方法有幾個大步驟便是以上內容了，如果您有什么不理解的就來網站www.mlzqjgx.cn咨詢吧。

　　There are several big steps in the installation method of high compartment is the above content, if you do not understand what to consult the website www.mlzqjgx.cn.