1、人員以正常速度從門外或門內走向感應門，感應門應該自動翻開，感應門的動作應該滑潤并且沒有出現磕碰的情況;感應門翻開后，人員以每秒約 150mm -200mm 的速度慢速通過感應門時，感應門應該堅持翻開情況。

1. Personnel should move towards the sensing door from outside or inside at normal speed, and the sensing door should automatically open. The movement of the sensing door should be smooth and there should be no collision; After the sensing door opens, when personnel slowly pass through it at a speed of approximately 150mm to 200mm per second, the sensing door should remain open.

2、 當人員脫離感應門感應器感應區后，在延時 1-10 秒后(時間長短可以由感應門開關參數來設置)，感應門將自動關閉，感應門的動作應該滑潤并且沒有出現磕碰的情況。

2. When a person leaves the sensing area of the sensing door sensor, after a delay of 1-10 seconds (the duration can be set by the sensing door switch parameters), the sensing door will automatically close, and the movement of the sensing door should be smooth and there should be no collision.

3、查詢人員正常通過感應門的行走路線，需求把日常行走路線調整為人員正對走向感應門，而不是以必定的角度走向感應門。

3. To check the normal walking route of personnel through the sensing door, it is necessary to adjust the daily walking route to direct the personnel towards the sensing door, rather than walking towards the sensing door at a certain angle.

4、走向感應門時，感應門感應器的感應寬度規劃應該大于門完全翻開的寬度。

4. When walking towards the sensing door, the sensing width planning of the sensing door sensor should be greater than the width of the fully opened door.

5、假定感應門設備了輔佐光線傳感器(紅外對射維護設備)，當門翻開時，人站著不動，用手遮擋輔佐光線傳感器，門應該堅持翻開情況。當手脫離后幾秒內，門應該從頭關閉。

5. Assuming that the sensing door is equipped with an auxiliary light sensor (infrared radiation maintenance equipment), when the door is opened, people should stand still and block the auxiliary light sensor with their hands, and the door should remain open. Within seconds after the hand disengages, the door should close from the beginning.

注意：

Attention:

1、不可以在溫度過高(50度以上)、過低(-20度以上)、潮濕、多塵土環境下運用。

1. It cannot be used in environments with high temperatures (above 50 degrees Celsius), low temperatures (above -20 degrees Celsius), damp or dusty conditions.

2、應在感應門上貼有提示標志。

2. Safety warning signs should be affixed to the sensing door.

3、濟南感應門在自動感應情況下運用時不可以擺放一些活動(或許風吹動會活動)的東西在門的感應頭檢測的規劃內，這會簡略構成感應門的誤運動動作產生

3. When using the Jinan induction door in automatic sensing mode, it is not allowed to place any moving objects (or things that may move when the wind blows) within the detection plan of the sensing head of the door, which will briefly cause misoperation of the induction door

4、不可以常常性在手掰動自動感應門，這會減低自動感應門的運用壽數。

4. It is not allowed to frequently move the automatic sensing door by hand, as this will reduce the service life of the automatic sensing door.

5、保證感應門、可靠地作業，用戶或感應門處理人員在日常需求對感應門進行必要的作業檢查和保養，好找人員進行。

5. Ensure the safe and reliable operation of the sensing door. Users or sensing door processing personnel should conduct necessary operational inspections and maintenance on the sensing door according to daily needs, and it is easy to find professional personnel to carry out.

感應門出現缺點時，請當即堵截感應門電源，然后可以聯系我們http://www.mlzqjgx.cn了解處理方法！

When there is a defect in the sensing door, please immediately cut off the power supply of the sensing door, and then you can contact us http://www.mlzqjgx.cn Understand the handling method!